18F26K22 Sigorta ayarları

[zeus48]

Arkadaşlar mrb. Bu piki şeçmemin sebebi 1.8 v  kadar çalışması. Bu işlemciyi tanımıyorum. Datasheet 
baktım birşey anlayamadım. Bana bu konuda yardımcı olurmusunuz. Dahili osc kullanacağım. 8mhz bana yeter

[Maxim]

1.8v çalışabilen 18LF versiyonudur (o da 20mhz altındayken)
normalleri 2.3 volt minimum

[zeus48]

Benim sorunum sigorta ayarlarını yapamamak

[Maxim]

bu dahili 8mhz osc için çalışan bir proton+ config ayarı

Device 18F26K22
Declare Xtal=8
    
OSCCON.6=1
OSCCON.5=1
OSCCON.4=0

OSCCON.1=1
OSCCON.0=1
;-------------------------------------------------------------------------------

Config_Start
  FOSC = INTIO67	;Internal oscillator block
  PLLCFG = OFF	;Oscillator used directly
  PRICLKEN = On	;Primary clock enabled
  FCMEN = OFF	;Fail-Safe Clock Monitor disabled
  IESO = OFF	;Oscillator Switchover mode disabled
  PWRTEN = On	;Power up timer enabled
  BOREN = SBORDIS
  BORV = 190
  WDTEN = OFF	;Watch dog timer is always disabled. SWDTEN has no effect.
  WDTPS = 32768	;1:32768
  CCP2MX = PORTC1	;CCP2 input/output is multiplexed with RC1
  PBADEN = On
  CCP3MX = PORTC6	;P3A/CCP3 input/output is mulitplexed with RC6
  HFOFST = On	;HFINTOSC output and ready status are not delayed by the oscillator stable status
  T3CMX = PORTC0	;T3CKI is on RC0
  P2BMX = PORTC0	;P2B is on RC0
  MCLRE = INTMCLR	;RE3 input pin enabled; MCLR disabled
  STVREN = OFF	;Stack full/underflow will not cause Reset
  LVP = OFF	;Single-Supply ICSP disabled
  XINST = OFF	;Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
  Debug = OFF	;Disabled
  Cp0 = On	;Block 0 (000800-001FFFh) code-protected
  CP1 = On	;Block 1 (002000-003FFFh) code-protected
  CP2 = On	;Block 2 (004000-005FFFh) code-protected
  CP3 = On	;Block 3 (006000-007FFFh) code-protected
  CPB = On	;Boot block (000000-0007FFh) code-protected
  CPD = OFF	;Data EEPROM not code-protected
  WRT0 = OFF	;Block 0 (000800-001FFFh) not write-protected
  WRT1 = OFF	;Block 1 (002000-003FFFh) not write-protected
  WRT2 = OFF	;Block 2 (004000-005FFFh) not write-protected
  WRT3 = OFF	;Block 3 (006000-007FFFh) not write-protected
  WRTC = OFF	;Configuration registers (300000-3000FFh) not write-protected
  WRTB = OFF	;Boot Block (000000-0007FFh) not write-protected
  WRTD = OFF	;Data EEPROM not write-protected
  EBTR0 = OFF	;Block 0 (000800-001FFFh) not protected from table reads executed in other blocks
  EBTR1 = OFF	;Block 1 (002000-003FFFh) not protected from table reads executed in other blocks
  EBTR2 = OFF	;Block 2 (004000-005FFFh) not protected from table reads executed in other blocks
  EBTR3 = OFF	;Block 3 (006000-007FFFh) not protected from table reads executed in other blocks
  EBTRB = OFF	;Boot Block (000000-0007FFh) not protected from table reads executed in other blocks
Config_End

[zeus48]

Üstad ilgin için tşk  . Basıc olanı lazım

[F®T]

Zeuse48 bu iş pdf yi okuyarak ancak yapılır.